View MC10E141_88320.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
8 Bit Shift Register
The MC10E/100E141 is an 8-bit full-function shift register. The E141 performs serial/parallel in and serial/parallel out, shifting in either direction. The eight inputs D0 - D7 accept parallel input data, while DL/DR accept serial input data for left/right shifting. The Qn outputs do not need to be terminated for the shift operation to function. To minimize noise and power, any Q output not used should be left unterminated.
MC10E141 MC100E141
8-BIT SHIFT REGISTER
* * * * * * *
700MHz Min. Shift Frequency 8-Bit Full-Function, Bi-Directional Asynchronous Master Reset Pin-Compatible with E241 Extended 100E VEE Range of - 4.2V to - 5.46V 75k Input Pulldown Resistors
The select pins, SEL0 and SEL1, select one of four modes of operation: Load, Hold, Shift Left, Shift Right, according to the Function Table. Input data is accepted a set-up time before the positive clock edge. A HIGH on the Master Reset (MR) pin asynchronously resets all the registers to zero. Pinout: 28-Lead PLCC (Top View)
SEL0 25 SEL1 CLK MR VEE DR D0 D1 26 27 28 1 2 3 4 5 D2 6 D3 7 D4 8 VCCO 9 Q0 10 Q1 11 Q2 DL 24 D7 23 D6 22 D5 21 VCCO 20 Q7 19 18 17 16 15 14 13 12 Q6 Q5 VCC NC VCCO Q4 Q3
FN SUFFIX PLASTIC PACKAGE CASE 776-02
FUNCTION TABLE
SEL0 L L H H SEL1 L H L H Function Load Shift Right (Dn to Dn+1) Shift Left (Dn to Dn -1) Hold
PIN NAMES
Pin D0 - D7 DL, DR SEL0, SEL1 CLK Q0 - Q7 MR Function Parallel Data Inputs Serial Data Inputs Mode Select In Inputs Clock Data Outputs Master Reset
* All VCC and VCCO pins are tied together on the die.
EXPANDED FUNCTION TABLE
Function Load Shift Right Shift Left Hold Reset
7/96
DL X X X L H X X X
DR X L H X X X X X
SEL0 L L L H H H H X
SEL1 L H H L L H H X
MR L L L L L L L H
CLK Z Z Z Z Z Z Z X
Q0 D0 L H L Q0 Q0 Q0 L
Q1 D1 Q0 L Q0 Q1 Q1 Q1 L
Q2 D2 Q1 Q0 Q1 Q2 Q2 Q2 L
Q3 D3 Q2 Q1 Q2 Q3 Q3 Q3 L
Q4 D4 Q3 Q2 Q3 Q4 Q4 Q4 L
Q5 D5 Q4 Q3 Q4 Q5 Q5 Q5 L
Q6 D6 Q5 Q4 Q5 L L L L
Q7 D7 Q6 Q5 L H H H L
(c) Motorola, Inc. 1996
2-1
REV 3
MC10E141 MC100E141
LOGIC DIAGRAM
DL BITS 1 - 6
D DR
Q R Q0
D D
Q R Q D7
D
Q R Q7
D0 SEL1 SEL0 CLK MR
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol IIH IEE Characteristic Input HIGH Current Power Supply Current 10E 100E 131 131 min typ max 150 181 181 131 131 min 25C typ max 150 181 181 131 151 min 85C typ max 150 181 181 Unit A mA Condition
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol fSHIFT tPLH tPHL ts Characteristic Max. Shift Frequency Propagation Delay To Output Clk MR Setup Time D SEL0 SEL1 Hold Time D SEL0 SEL1 Reset Recovery Time Minimum Pulse Width Clk, MR Within-Device Skew Rise/Fall Times 20 - 80% 300 min 700 typ 900 max min 700 25C typ 900 max min 700 85C typ 900 max Unit MH z ps 625 600 175 350 300 200 100 100 900 400 60 525 800 300 750 725 25 200 150 - 25 - 200 -150 700 975 975 625 600 175 350 300 200 100 100 900 400 60 525 800 300 750 725 25 200 150 - 25 - 200 -150 700 975 975 625 600 175 350 300 200 100 100 900 400 60 525 800 ps ps 1 750 725 25 200 150 ps - 25 - 200 -150 700 ps ps 975 975 ps Condition
th
tRR tPW tSKEW tr tf
1. Within-device skew is defined as identical transitions on similar paths through a device.
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E141 MC100E141
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E141 MC100E141
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E141/D*
MC10E141/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E141

	To Download MC10E141 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .